National Luna Equipment

 

Split Charge Systems:

The Split-charge kit will monitor the state of your batteries and the charging source. Connection is automatic, so you don't have to remember to connect your auxilliary battery whilst driving. The Split-charge controller will automatically isolate the auxilliary battery when the batteries are no longer receiving a charge voltage.

The Split-charge kit consists of: Intelligent solenoid, Dual battery monitor, plug-in monitor cable, 6m each 16mm black and red double insulated cable, in-line power fuses, battery terminals, screws, lugs, cable ties and full installation guide.

This kit has everything you need for a D-I-Y split charge installation. For non-standard installations, higher gauge cable is available up to 35mm. Batteries are not included

Intelligent Solenoid

The Intelligent Solenoid is the heart of the split-charge system and can be used as a stand-alone isolator. This device monitors both MAIN and AUXILIARY batteries in a vehicle and connects the auxilliary battery when the main battery is receiving sufficient charge. The isolator is automatic, no input is required from the user. Voltage sensing, timing and all calculations are done internally. Important safety features and parameters have been pre-programmed into the operation of this system. This system does not interfere with existing vehicle wiring. No igrition wire is required.

The Intelligent solenoid is supplied with a basic hardware kit and manual. Batteries, cables and terminals are not supplied.

 

 

The new battery monitor range has been designed to cover a variety of applications where it is important to monitor the state of a battery. Using digital technology, the new battery monitors constantly measure the voltage of your battery and warn you when the battery is getting flat or when the battery is being overcharged. Visual and audible alarms are standard on most models. Features such as alarm silence and sleep mode are also available.

All battery monitors in the range are simple to install and at the same time reliable and very accurate.
 
3

Single battery monitor

This monitor is a low-cost, accurate battery capacity meter. Featuring digital technology, the single battery monitor measures the terminal voltage of a single 12-volt lead-acid battery and converts the voltage into a simple-to-read graph.

The graph is split into 3 colour areas so that at a quick glance, you can know if your battery is OK. The single monitor has built-in excessive-discharge and overcharge identification and visual alarm.

Supplied with 3.5 metre flex cable.

4

Single battery monitor (With audible alarm)

This version of the single battery monitor has a built-in audible alarm. The monitor identifies conditions of excessive-discharge and over-charge. If any of these conditions are reached, the monitor will warn the user with a visual and audible alarm. The alarm on this single monitor can be disabled at any time. If you don't need to see the state of your battery all of the time, the display can be turned off as well. In this mode, the monitor still functions normally and will wake if any error occurs.

The single battery monitor is supplied with 3.5 meters of cable.
2

Dual battery monitor (With dual audible alarm)

Designed especially for dual battery 12-volt and 24-volt systems, this monitor measures two batteries at the same time. The Dual battery monitor has all the features of the single monitor, but has two separate displays with over-charge and excessive-discharge alarms. Each of the two displays have their own alarms which can be turned off independently of each other. The two displays can also be turned off independently. This monitor can be used with almost any existing dual-battery system.

This monitor has an independent-negative system, and is perfect for two-battery 24-volt systems. Supplied with 3 or 6 meters of cable.
1

Dual battery controller (With audible alarm)

This version of the Dual Battery Monitor is a companion to the National Luna split-charge system. The monitor is supplied with a removeable cable which connects to either the Intelligent Solenoid or Portable Power Pack, no other wiring is necessary. The monitor uses high-accuracy digital technology to measure your batteries several times per second and display battery status in an easy-to-read manner. This monitor is also compatible with older versions of the National Luna split-charge system.

Featuring over-charge and excessive-discharge detection, visual and audible alarm, alarm silence, SLEEP mode and timer override facility. All packed into a compact, stylish package. The plug-in cable is available in 3 meter or 6 meter lengths.